Meade SmartFinder Bedienerhandbuch Seite 27
- Seite / 60
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
27
Tracking Rate: Changes the speed at which the telescope tracks targets in the
sky.
a. Sidereal: The default setting for AutoStar; sidereal rate is the standard rate
at which stars move from East to West across the sky due to the rotation of
the Earth.
b. Lunar: Choose this option to properly track the Moon over long observing
sessions.
c. Custom: Allows entry of user-defined tracking rates.
Reverse L/R: Reverses the functions of the Left and Right Arrow keys (
i.e.
, the
Right key moves the telescope to the left)
.
Reverse UP/DOWN: Reverses the functions of the Up and Down Arrow keys
(
i.e.
, the Up key moves the telescope down)
.
Calibrate Sensors: This menu allows you to improve your telescope's pointing
accuracy to alignment stars. It calibrates to correct slight mechanical misalign-
ment due to transport, vibration, or aging. It is recommended that calibration be
performed after the LNT Module batteries are changed (see page 56 for more
information).
When this menu is selected, the telescope slews to Polaris. AutoStar then
prompts you to center Polaris and to press ENTER. AutoStar uses the position of
Polaris to fine tune the position of North and also for detecting level.
Quiet Slew: Sets the maximum slew rate to 1.5° for quieter operation.
Max Elevation: Allows you to enter a value in degrees that sets a limit as to how
far the optical tube can swing upward during a programmed slew. (Note that it
does not prevent you from performing a manual slew past this limit.) This is
useful when you have a camera or other peripheral attached to the telescope—
you can prevent it from striking the telescope base.
Min AOS (Acquisition of Signal): Allows you enter a value in degrees. This
value represents the altitude at which your telescope begins to slew when
acquiring a satellite track. This is useful when you are observing satellites, but a
tall tree or building is obstructing the telescope. For example, you might begin to
track the satellite at 15° altitude, instead of 5°. See OBSERVING SATELLITES,
page 30, for more information about satellites.
Calibrate Motor: If the telescope motors appear to have a problem, use this
option to retest the motors before performing a Reset. This option is also used if
an AutoStar unit is moved between telescopes, to match AutoStar to the new tel-
escope. To calibrate the motors, select this option and press ENTER.
Smart Drive: Allows you to perform periodic error correction (PEC) on the R.A.
worm gear and can only be used with polar mounted telescopes. Must be
performed with a high powered reticle (
eg. 9mm
). PEC Training for the the ETX
telescopes will take about 24 minutes.
High Precision: If High Precision is turned on, when looking for a faint celestial
object (
i.e.
, a nebula or galaxy), AutoStar first slews to a nearby bright star and
displays "ENTER to Sync." Center the star in the eyepiece, then press ENTER.
At that point the telescope has a high precision alignment to that part of the sky
and it then slews to the object that was originally requested.
Targets switches between Astronomical targets and Terrestrial targets. If
"Astronomical" is selected, the telescope tracking motor is activated and any object
you observe will remain centered in the eyepiece. If "Terrestrial" is selected and the
telescope is aligned, the tracking motor is turned off. To learn how to track an object
automatically, see page 16.
Site provides access to several options including:
Select: Displays the currently selected observing site or zip code. Use the Scroll
keys to cycle through all the sites. Press ENTER when the site you wish to select
displays. Use this option when you move to a different
geographic location. The cities you have chosen or zip codes you have “added”
will appear at the top of this list (see
ADD below).
Tip:
If the "ENTER to Sync"
feature is accessed by
mistake (holding the
ENTER key for more than
2 seconds), press MODE
to return to the previous
screen.
Want to learn more about
Periodic Error
Correction
? See page 37.
Premium ETX_without 105.qxd 1/27/09 12:33 PM Page 27
- Instruction Manual 1
- CONTENTS 3
- QUICK-START GUIDE 4
- 29 for more information 5
- TELESCOPE FEATURES 6
- MEADE ETX: YOUR PERSONAL 7
- WINDOW TO THE UNIVERSE 7
- 1( Note: 8
- Fig. 4: The AutoStar Handbox 9
- Want to learn more about 9
- ? See pages 28 9
- Want to learn more 11
- ? See page 16 11
- Battery installation 12
- Spread tripod legs 12
- Slide spreader on rod 12
- Tension knob assembly 12
- Adjust tripod height 12
- Attach telescope to 13
- : Meade Super 14
- Plössl eyepieces 14
- : Turn the top (13) or 14
- OBSERVING 15
- Slew Speeds 16
- Astronomical Observing 16
- Observe the Moon 16
- Automatic Alignment 17
- Spiral Search 17
- ETX TIPS 17
- Using the Guided Tour 18
- Go To Saturn 18
- Initializing AutoStar 19
- AUTOSTAR OPERATION 20
- Look into the Future 21
- Entering data into AutoStar 21
- AUTOSTAR'S MENUS 22
- Object Menu 23
- Event Menu 24
- Glossary Menu 24
- Utilities Menu 25
- Setup Menu 26
- ADVANCED AUTOSTAR 29
- OPERATION 29
- Sky & Telescope 30
- Astronomy) 30
- PHOTOGRAPHY WITH 31
- MEADE’S AUTOSTAR SUITE 31
- OPTIONAL ACCESSORIES 31
- Interactive Mode: 32
- In Interactive Mode 32
- In Automatic Mode 32
- Identify 35
- Advanced Alt/Az Alignment 36
- Observing Considerations 37
- PHOTOGRAPHY 39
- The Deep Sky Imager 41
- The Lunar Planetary Imager 41
- MAINTENANCE 44
- Troubleshooting 45
- SPECIFICATIONS 47
- Specifications: 48
- ETX-125PE Astro Telescope 48
- Telescope dimensions: 48
- For example 49
- Astronomy 49
- APPENDIX A: EQUATORIAL 50
- (POLAR) ALIGNMENT 50
- Fig. 46: 51
- Fig. 45: 51
- Fig. 44: 51
- Fig. 47: 52
- Fig. 48: 52
- Fig. 49: 52
- APPENDIX B: LATITUDE CHART 54
- Star Gazer 55
- APPENDIX D:CHANGING THE 56
- LNT MODULE BATTERY 56
- Fig. 57: The Moon. Note 57
- MEADE LIMITED WARRANTY 60
Verwandte Produkte und Handbücher für Teleskope Meade SmartFinder
Teleskope Meade ETX-60AT Bedienungsanleitung
(40 Seiten)
(40 Seiten)
Teleskope Meade 90AZ-ADRB Bedienerhandbuch
(12 Seiten)
(12 Seiten)
Teleskope Meade ETX-105PE Bedienerhandbuch
(60 Seiten)
(60 Seiten)
Teleskope Meade DS-80 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Teleskope Meade 70AZ-ADR Bedienerhandbuch
(12 Seiten)
(12 Seiten)
Teleskope Meade LX10 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Teleskope Meade ETX-125PE Bedienerhandbuch
(28 Seiten)
(28 Seiten)
Teleskope Meade RCX400 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Teleskope Meade Starfinder 16 Bedienerhandbuch
(16 Seiten)
(16 Seiten)
Teleskope Meade LX10 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Teleskope Meade Autostar Bedienerhandbuch
(31 Seiten)
(31 Seiten)
Teleskope Meade 70AZ-ADS Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Teleskope Meade MAX-ACF Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Teleskope Meade LX20 Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Teleskope Meade Autostar Bedienerhandbuch
(38 Seiten)
(38 Seiten)
Husqvarna COOKER,QSI6272 230V manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour mélangeurs/transformateurs d'aliments Husqvarna COOKER,QSI6272 230V.
Nous fournissons des manuels en pdf 1 Husqvarna COOKER,QSI6272 230V à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern